Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
TouchOsc Info
10-08-2015, 03:28 PM
Post: #1
TouchOsc Info
Hello to all,
I wanted to know if when I press "ZERO" the slides touch osc you bring in a neutral position or remain where they are.
greetings VL
Find all posts by this user
Quote this message in a reply
10-10-2015, 08:03 PM
Post: #2
RE: TouchOsc Info
Can anyone tell me if when I hit zero the slides go to zero
greetings VL
Find all posts by this user
Quote this message in a reply
10-10-2015, 09:18 PM
Post: #3
RE: TouchOsc Info
Hello

The slides stay where they are when you hit "zero"

Patrick
Find all posts by this user
Quote this message in a reply
10-11-2015, 01:25 PM
Post: #4
RE: TouchOsc Info
Hi I have a problem, the robot tends to go forward, but sometimes it works perfectly.
What can be? IMU cables are shielded.
regards Vito
Find all posts by this user
Quote this message in a reply
10-11-2015, 01:40 PM
Post: #5
RE: TouchOsc Info
Look for angle_adjusted values in Debug mode. Maybe MPU6050 is not horizontal..
Find all posts by this user
Quote this message in a reply
10-11-2015, 02:29 PM
Post: #6
RE: TouchOsc Info
when in debug mode read 0, the robot is moved to 6-7gradi, the MPU6050 is horizontal.
Before it worked well after some editing was busted, but I put the original firmware and it does not work, or the robot goes forward.bv
Find all posts by this user
Quote this message in a reply
10-11-2015, 03:07 PM
Post: #7
RE: TouchOsc Info
To find what is wrong try check together angle_adjusted, fadder1 and throttle values through Serial.print(). Values must be 0, 0.5 and 0 for robot vertical position.
Is robot moves forward when no connection to OSC (mobile phone) too? And after restart too?
For test you can add some correction angle like this - angle_adjusted = dmpGetPhi() - your error angle; and look what happens.
Find all posts by this user
Quote this message in a reply
10-11-2015, 03:21 PM
Post: #8
RE: TouchOsc Info
Why sometimes it works and sometimes not?
start the robot has to be horizontal or at any location?
greetings VL
Find all posts by this user
Quote this message in a reply
10-11-2015, 03:53 PM (This post was last modified: 10-11-2015 03:54 PM by KomX.)
Post: #9
RE: TouchOsc Info
(10-11-2015 02:29 PM)vlelectronic Wrote:  when in debug mode read 0, the robot is moved to 6-7gradi, the MPU6050 is horizontal.

Turn the robot upside down. Print it, relying on wheels, like a normal pendulum. To axis of one of the wheels attach a conventional plummet. If the vertical axis of the side of the robot does not coincide with the plumb thread, then balance the internal contents of the robot. Typically, a small movement of the battery back and forth enough.
Find all posts by this user
Quote this message in a reply
11-04-2015, 05:01 PM
Post: #10
RE: TouchOsc Info
Hello to all,
I always have the problem with the balance that is not in balance, I put, as he says sasa999, -9 degrees which is the angle of my error, but I notice that the controls do not respond well when steering the robot before making a wheel ahead and a back but after a stop, and after a 'little falls.
Anyone can help me?
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)